Rest In Peace
Cattails
Dine Out
The Water Cooler
The Class Of 1979
Senior Hijinks
Varsity Cheerleaders
Mrs. Roy, High School Librarian
Seniors Do It Better
Greasers
One Cool Cat
Happy Birthday
Black and White Sunset
Dining At The Mexican Restaurant
I Feel Like Chicken Tonight
Stone Lion
Mexican Food
Ice Cream Sandwich
Christmas Sunset
Lemon Meringue Pie
Through A Sawhorse Darkly
Flowers
Meringue
Light Side Of The Moon
CE3K Abduction Scene
Prom Night
Sir D.J. Rappafellow
The Austins
Sport Camera One-Time-Use 35mm Stripped
Smokestack
Kodak Easy Share C433
Blur (Whoo Hoo)
Old Building
Sundown
Monarch Butterfly
1962 Oldsmobile Starfire Convertible
Yashica FX-7 Super
Yashica FX-3
Minolta XG1 No. 3
Minolta X-7A No. 3
Minolta SRT-201
Minolta SRT-200
Konica FS-1
Konica Autoreflex TC No. 5
Imperial Magimatic X-50 No. 3
See also...
Keywords
Authorizations, license
-
Visible by: Everyone -
All rights reserved
-
486 visits
Carena DF-300 Capacitor Repair
Last night I soldered a new capacitor into my Carena DF-300 and now it works perfectly! There was a known capacitor issue in the Minolta X-300/X-370 cameras where a cheaper capacitor was used and it goes bad a lot of the times. This Carena DF-300 is a fully licensed copy of the Minolta X-300 and it was made in China, so this fix applies to the X-300/X-370 in general.
To describe the capacitor issue, I've found that if the camera has fresh batteries, you turn on the camera and use the self-timer mode. If the light on the front of the self-timer flashes properly and then the camera just does nothing after 10 seconds, this indicates the capacitor is bad and needs replacing. This has always been the case for me, because I have about 17 of these Minolta cameras and licensed copies and a half-dozen or so has needed a new capacitor.
The white arrow points to the area where the capacitor is. Between the base plate and the bottom of the camera, you can see one of the new, thinner capacitors and the older, fatter one I replaced. Hope this helps everybody out there who wants to fix their cameras. It's really not that hard of a job to do. I also want to point out that it seems you need to put the new capacitor in in a certain way. Along one side of the capacitor seems to be arrow point down. These need to go to the right side as show in the picture above - to the outer edge of the camera. I'm not sure if this makes a difference, but I must have got a few installed backwards and when I refixed them, keeping the arrows to the correct side, this has solved the problem. Your mileage may vary, of course.
As an additional aid, to take off the base plate, there are four tiny screws that hold it on. Two longer ones on each end and two shorter ones toward the middle. I've found that the two longer ones are usually the hardest to get loose, while the two shorter ones come out real easy. And that's all there is to getting into where the capacitor is located.
To describe the capacitor issue, I've found that if the camera has fresh batteries, you turn on the camera and use the self-timer mode. If the light on the front of the self-timer flashes properly and then the camera just does nothing after 10 seconds, this indicates the capacitor is bad and needs replacing. This has always been the case for me, because I have about 17 of these Minolta cameras and licensed copies and a half-dozen or so has needed a new capacitor.
The white arrow points to the area where the capacitor is. Between the base plate and the bottom of the camera, you can see one of the new, thinner capacitors and the older, fatter one I replaced. Hope this helps everybody out there who wants to fix their cameras. It's really not that hard of a job to do. I also want to point out that it seems you need to put the new capacitor in in a certain way. Along one side of the capacitor seems to be arrow point down. These need to go to the right side as show in the picture above - to the outer edge of the camera. I'm not sure if this makes a difference, but I must have got a few installed backwards and when I refixed them, keeping the arrows to the correct side, this has solved the problem. Your mileage may vary, of course.
As an additional aid, to take off the base plate, there are four tiny screws that hold it on. Two longer ones on each end and two shorter ones toward the middle. I've found that the two longer ones are usually the hardest to get loose, while the two shorter ones come out real easy. And that's all there is to getting into where the capacitor is located.
Frans Schols has particularly liked this photo
- Keyboard shortcuts:
Jump to top
RSS feed- Latest comments - Subscribe to the comment feeds of this photo
- ipernity © 2007-2024
- Help & Contact
|
Club news
|
About ipernity
|
History |
ipernity Club & Prices |
Guide of good conduct
Donate | Group guidelines | Privacy policy | Terms of use | Statutes | In memoria -
Facebook
Twitter
Maar dat wist jij natuurlijk al lang.....
Hartelijke groeten.........Frans
HaarFager club has replied to Frans Schols clubSign-in to write a comment.